[Q50-Q71] Updated Jun-2022 Exam Engine or PDF for the 300-615 Tests Free Updated Today!

4.5/5 - (2 votes)

Updated Jun-2022 Exam Engine or PDF for the 300-615 Tests Free Updated Today!

Ultimate Guide to Prepare 300-615 with Accurate PDF Questions

Q50.

Refer to the exhibit. An engineer deploys a SAN environment with two interconnected Cisco MDS 9000 Series Switches. When the engineer attempts a zone merge, it fails with the error that is presented in the exhibit.
Which action resolves the issue?

Import or export a zone set between the switches to synchronize the switches.

Change the name of one of the zones to match the other zone set.

Ensure that the zone members have different names.

Set the distribute policy of the zone to full.

Q51. DRAG DROP
Drag and drop the Cisco UCS SNMP fault types from the left onto the correct issues on the right.
Select and Place:

Q52. Refer to the exhibit.

The vPC between switch1 and switch2 does not work. Which two actions resolve the problem? (Choose two.)

Configure the IP address on the interface.

Activate VLANs on the vPC.

Configure one of the switches as primary for the vPC.

Correct the configuration of the vPC peer link and the vPC peer keepalive.

Match the vPC domain ID between the two devices.

Q53. A request to activate the port security database is rejected. Which action do you perform to investigate the cause of the issue?

Enable the auto-learning feature.

Use the force option to identify rejected devices.

Find conflicting entries between the active and configuration databases.

Verify that devices are fully attached to the active database.

Q54. A mission-critical server is connected to site A. Connectivity to this server is lost from site B because the MAC route is missing in the OTV VDC of the Nexus 7000 in site B due to MAC aging. Which action allows the flooding of the unknown unicast MAC on the Nexus 7000 in the OTV VDC?

Use route-map to advertise this MAC statically and redistribute with ISIS.

Unknown unicast flooding is not allowed.

Use the otv flood mac <> command to selectively flood traffic for a given MAC.

Use the otv isis bfd <> command to configure BFD protocol.

Q55. Refer to the exhibit.

The HSRP configuration in the exhibit fails to function. Which action resolves this issue?

Enable IP redirects.

Set the MTU to 1500 bytes.

Configure HSRP version 2.

Configure the same HSRP group on both devices.

Q56. Refer to the exhibit.

Cisco UCS Manager is being upgraded using the Auto Install feature, but the FSM fails. Which action resolves the issue?

Acknowledge the primary fabric interconnect.

Remove the service pack from the subordinate fabric interconnect.

Clear the startup version of the default infrastructure pack.

Upgrade the firmware of the infrastructure firmware by using the force option.

Q57. Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?

Modify the VLAN assignment to vNICs.

Change the PIN groups on the vHBAs.

Modify the FCoE VLAN.

Set the FCoE VLAN as the native VLAN on server uplinks.

Q58. A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?

Verify that the SFPs are supported.

Change the SFP to operate at 4 Gbps instead of 2 Gbps.

Run the shutdown and then no shutdown command on the interface.

Run the switchport ignore bit-errors command on the interface.

Q59. An engineer troubleshoots a failed DCBX exchange between a server and a Cisco Nexus switch. Which action allows DCBX to successfully negotiate?

Enable ETS.

Enable PFC.

Enable Cisco Discovery Protocol.

Enable LLDP.

Q60. Refer to the exhibit.

A network engineer has connected the Nexus switch management port to the Internet using DHCP to allow the Guest shell running on the switch to download Python packages. The engineer can ping google.com successfully from the Nexus switch, but the Guest shell failed to download any Python packages. Which action resolves the problem?

Update the Python packages on the Cisco Nexus switch directly.

Manually configure DNS in the Guest shell, even if it is claimed on the Cisco Nexus switch through DHCP.

Manually configure NTP in the Guest shell.

Connect Guest shell to data plane interfaces to be able to connect to the networks outside the Cisco Nexus switch.

Q61. An engineer must upgrade all components in a Cisco UCS domain to the same package version, but the upgrade process fails to complete. Which set of Auto Install actions resolves the problem?

Install Infrastructure Firmware, then Install Server Firmware.

Install infrastructure Firmware, then Install Hypervisor Firmware.

Install Hypervisor Firmware, then Install Infrastructure Firmware

Install Server Firmware, then Install Infrastructure Firmware

Q62. Refer to the exhibit.

An engineer discovers that if the vPC peer link goes down, half of the devices in VLAN 20 experience connectivity issues with the external networks Which action resolves the issue?

Configure a dedicated Layer 3 link between vPC peers

Allow non-vPC VLANs on a second trunk between the two vPC peers

Add the non-vPC SVIs in the dual-active exclude VLAN list

Exclude the non-vPC VLANs from vPC peer link

Q63. Refer to the exhibit.

An engineer deploys SAN environment with two interconnected Cisco MDS 9000 Series switches. When the engineer attempts a zone merge, it fails with the error that is presented in the exhibit. Which action resolves the issue?

Import or export a zone set between the switches to synchronize the switches.

Change the name of one of the zones to match the other zone set.

Set the distribute policy of the zone to full.

Ensure that the zone members have different names.

Q64. Refer to the exhibit.

A network engineer traces the packet flow from the Veth991 of a blade server toward the core switch. The switch reports performance issues What is the role of the interface Eth1/7?

IOM network interface

fabric interconnect uplink interface

IOM host interface

server interface

Q65. A fabric interconnect fails to start and the console displays the loader prompt. Which two actions resolve the issue? (Choose two.)

Load an uncorrupt bootloader image.

Load an uncorrupt kickstart image.

Reconnect L1/L2 cables between the Fis.

Reformat the fabric interconnect.

Load the correct version of the boot image.

Q66. A Fibre Channel interface on a Cisco Nexus 5000 Series Switch receives bit errors, and the switch disables the interface. A temporary workaround must be implemented before the root cause is identified. Which action does an engineer take to prevent this issue from reoccurring?

Verify that the SFPs are supported.

Change the SFP to operate at 4 Gbps instead of 2 Gbps.

Run the shutdown and then no shutdown command on the interface.

Run the switchport ignore bit-errors command on the interface.

Q67. A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image. Drag and drop the recovery steps from the left onto the correct order on the right.

Q68. Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.

Q69. A network engineer discovers a DNS resolution problem on a device that is using the Cisco Nexus Bash shell.
The device name is app with an IP address of 10.10.10.1. The primary server IP address is 172.16.10.1 and the secondary server IP address is 172.16.10.2. When the abc.com resolution fails, it should attempt to use efg.com. Which settings must be added to resolv.conf file to resolve the issue?

Option A

Option B

Option D

Q70. Refer to an exhibit.

An engineer is troubleshooting an upgrade failure on a switch. Which action resolves the issue?

Save the system image in NVRAM.

Use the same system image as the kickstart image.

Load a new system image.

Reload the same system image.

Q71. An engineer must configure Linux hosts that are deployed on Cisco UCS B-Series Servers to boot from SAN. The SAN boot policy is configured in Cisco UCS Manager, and the boot order is verified to be set as expected However, the Linux hosts fail to boot. Which action resolves the issue?

Remove all of the local storage that is installed

Delete and reconfigure the pWWN of the SAN boot target

Remove all of the ISO images that are mounted as a virtual CD-ROM

Delete and reconfigure the boot LUN