Latest Fortinet NSE6_FSW-7.2 Dumps for success in Actual Exam Nov-2024 [Q24-Q42]

4.3/5 - (3 votes)

Latest Fortinet NSE6_FSW-7.2 Dumps for success in Actual Exam Nov-2024]

Realistic NSE6_FSW-7.2 100% Pass Guaranteed Download Exam Q&A

Fortinet NSE6_FSW-7.2 exam covers a range of topics related to the FortiSwitch 7.2, including switch administration, VLANs, STP, LACP, FortiLink, FortiNAC, and FortiTelemetry. NSE6_FSW-7.2 exam is designed to test the candidate’s proficiency in configuring and managing Fortinet switches in an enterprise environment.

Fortinet NSE6_FSW-7.2 certification exam covers various topics that include FortiSwitch hardware and software architecture, VLAN configuration, spanning tree protocol, and security policies. NSE6_FSW-7.2 exam is designed to test your knowledge and skills in managing FortiSwitch networks and implementing security policies. Fortinet NSE 6 – FortiSwitch 7.2 certification exam is ideal for network administrators, security professionals, and engineers who want to enhance their career prospects in the network security domain.

QUESTION 24
Refer to the configuration:

Which two conditions does FortiSwitch need to meet to successfully configure the options shown in the exhibit above? (Choose two.)

The FortiSwitch model is equipped with a maximum of 54 interfaces

FortiSwitch would need to be rebooted.

The split port can be assigned to a native VLAN.

The Dort full speed prior to the split was 100G QSFP+.

QUESTION 25
Refer to the exhibit.

Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface. After FortiGate authorizes and manages Core-2. Port1 status becomes STP discarding.
Why is port1 in the discarding state?

port1 on Core-2 is discarding only management traffic.

Core-1 and Core-2 do not have MCLAG configuration.

Access-1 is the root bridge and can only have one root port.

Core-2 has the lowest bridge priority.

QUESTION 26
How is traffic routed on FortiSwitch?

Hardware-based routing on FortiSwitch is handled by the CPU.

FortiSwitch looks up the hardware routing table and then the forwarding information base (FIB).

ASIC hardware routing can only handle dynamic routing, if supported.

Layer 3 routing can be configured on FortiSwitch, while managed by FortiGate.

QUESTION 27
How are the ‘by VLAN redirect MAC address quarantine’ mode and the ‘by redirect MAC address quarantine’ mode on FortiGate similar?

Both modes move quarantined devices to the quarantine VLAN.

Both modes require firewall policies to block inter-VLAN traffic.

Both modes add quarantined device MAC addresses to the blocked firewall address group.

Both modes block intra-VLAN traffic by FortiGate automatically.

QUESTION 28
Exhibit.

You need to manage three FortiSwitch devices using a FortiGate device. Two of the FortiSwitch devices initiated a reboot after the authorization process. However, the FortiSwitch device with the configuration shown in the exhibit. did not reboot All three devices completed FortiLink manage-ment authorization successfully.
Why did the FortiSwitch device shown in the exhibit not reboot to complete the authorization pro-cess?
The management mode was set to use FortiLink mode.

Switch auto-discovery is enabled.

The management mode was set to use FortiLink mode.

The FortiSwitch device is scheduled to reboot as part the authorization process

The system time is not in-sync and is using a non-default value

QUESTION 29
To enhance service in emergency situations, to which LLDP-MED Type-Length-Values does Forti-Switch advertise to IP phones?

Network policy

Inventory management

Location

Power management

QUESTION 30
What can an administrator do to maintain a FortiGate-compatible FortiSwitch configuration when changing the management mode from standalone to FortiLinK?

Use a migration tool based on Python script to convert the configuration.

Enable the FortiLink setting on FortiSwitch before the authorization process.

FortiGate automatically saves the existing FortiSwitch configuration during the FortiLink management process.

QUESTION 31
What type of multimode transceiver can be used to split a 40G port?

QSFP+ transceiver

SFP transceiver

QSFP transceiver

SFP+ transceiver

QUESTION 32
Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?

All ports have auto-discovery enabled by default.

No ports are enabled by default for auto-discovery. This must be configured under config switch interface.

The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.

The last four switch ports on FortiSwitch have auto-discovery enabled by default.

QUESTION 33
Which two statements about 802.1X authentication on FortiSwitch ports are true? (Choose two.)

All hosts behind an authenticated port are allowed access after a successful authentica-tion.

A security policy is used to apply 802.1 authentication on a port.

A local user database must be used to authenticate devices using the 802.1X authentica-tion protocol.

All devices connecting to FortiSwitch must support 802.1X authentication.

QUESTION 34
Refer to the diagnostic output:

Two entries in the exhibit show that the same MAC address has been used in two different VLANs. Which MAC address is shown in the above output?

It is a MAC address of FortiLink interface on FortiGate.

It is a MAC address of a switch that accepts multiple VLANs.

It is a MAC address of an upstream FortiSwitch.

It is a MAC address of FortiGate in HA configuration.

QUESTION 35
Which statement about the IGMP snooping querier when enabled on a VLAN is true?

Active multicast receiver entries are aging on each IGMP query sent on the VLAN

IGMP reports on the VLAN are forwarded to all switch ports.

The setting can only be enabled using the FortiSwitch CLI.

All other indirectly connected switches will be unable to get IGMP multicast traffic.

QUESTION 36
FortiGate is unable to establish a tunnel with the FortiSwitch device it is supposed to manage Based on the debug output shown in the exhibit, what is the reason for the failure?

The handshake process timed out before FortiSwitch responded.

DTLS client hello had the incorrect pre-shared key.

The CAPWAP tunnel failed to come up due to a mismatch in time.

FortiSwitch has disabled FortiLink and is only managed as a standalone.

QUESTION 37
What are two ways in which automatic MAC address quarantine works on FortiSwitch? (Choose two.)

FortiSwitch supports only by VLAN quarantine mode.

FortiGate applies the quarantine-related configuration only on FortiGate.

FortiAnalyzer with a threat detection services license is required.

MAC address quarantine can be enabled through the FortiGate CLI only.

QUESTION 38
Exhibit.

What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)

The FortiSwitch model is equipped with a maximum of 54 interfaces.

The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.

The port full speed prior the split was 100G SFP+

The split port can be assigned to native VLAN

QUESTION 39
Refer to the exhibit.

Which two statements best describe what is displayed in the FortiLink debug output shown in the exhibit? (Choose two.)

FortiSwitch is sending FortiLink heartbeats to FortiGate.

FortiSwitch is discovered and authorized by FortiGate.

FortiSwitch is in a waiting state to join the stack group on FortiGate.

FortiSwitch is ready to push its new hostname to FortiGate.

QUESTION 40
What can an administrator do to maintain the existing standalone FortlSwltch configuration while changing the management mode to FortLink?

Use a migration tool based on python script to convert the configuration

Enable the Forti-link setting on FortiSwitch before the authorization process

FortiGate will automatically save the existing FortiSwitch configuration during the Forti-link management process.

QUESTION 41
Refer to the diagnostic output:

What makes the use of the sniffer command on the FortiSwitch CLI unreliable on__port__23?

The types of packets captured is limited.

Just the port egress payloads are printed on CLI.

Only untagged VLAN traffic can be captured.

The switch port might be used as a trunk member

QUESTION 42
Exhibit.

port24 is the only uplink port connected to the network where access to FortiSwitch management services is possible. However, FortiSwitch is still not accessible on the management interface. Which two actions should you take to fix the issue and access FortiSwitch? (Choose two.)