Free FlashArray-Implementation-Specialist Sample Questions and 100% Cover Real Exam Questions (Updated 77 Questions) [Q40-Q63]

5/5 - (1 vote)

Free FlashArray-Implementation-Specialist Sample Questions and 100% Cover Real Exam Questions (Updated 77 Questions)

Download Real Pure Storage FlashArray-Implementation-Specialist Exam Dumps Test Engine Exam Questions

NEW QUESTION 40
What is the minimum AC voltage required to operate a FlashArray//X20R4 array?

180

220

NEW QUESTION 41
A customer would like to reduce SafeMode settings for retention and eradication with their current policy.
How is authorization obtained to make the requested changes?

A Pure1 Admin needs to approve any changes for Pure Support to proceed.

Two SafeMode approvers need to acknowledge via Pure1 step-up authentication before any changes can be made.

The local account on FlashArray needs to permit any local changes.

NEW QUESTION 42
If a Technical Support Engineer (TSE) is not available to perform health checks after an installation, what action should the Implementation Engineer take?

Email the account team

Update and close the case.

Verify that Remote Assist (RA) is open and update the case.

NEW QUESTION 43
An Implementation Engineer is scheduled to install a FlashArray and a DirectFlash Shelf (DFS).
What action should the Implementation Engineer perform?

Refer to the “Recommended DFS Versions for Purity Releases” KB and upgrade Purity on the FlashArray and DFS.

Install the Array and DFS with the Purity that shipped and have Support upgrade remotely.

Only upgrade the Purity on the FlashArray and then attach the DFS.

NEW QUESTION 44
What are the interface names for a 4-port FC card in slot 1 in an XR2/3 array?

FC0, FC1, FC2, and FC3

FC4, FC5, FC6, and FC7

FC5, FC6, FC7, and FC8

NEW QUESTION 45
A customer has ordered several FlashArrays and wants to have ActiveCluster configured. What is the maximum quantity of arrays supported with ActiveCluster?

NEW QUESTION 46
What is the required PSU wattage for a FlashArray// X70R2/R3 or X90R2/R3 array?

1200W

1300W

1600W

NEW QUESTION 47
A customer has a FlashArray X20R3 with 22/22 data packs in the chassis at 80% space usage and wishes to swap one of the data packs for a 45TB pack. What step needs to be taken to facilitate this consolidation?

Send a DirectFlash Shelf without any additional capacity.

Send a DirectFlash Shelf with a 63TB of temporary extra capacity.

Reduce array space usage to allow for the evacuation of the 22TB packs.

NEW QUESTION 48
An Implementation Engineer performs a controller upgrade. What is the command to check I/O health?

purehost list –all

pureport list –initiator

purehost monitor –balance

NEW QUESTION 49
On a FlashArray//XR50R2/3 Fibre Channel (FC) array, what is the default type and placement of the PCIe FC card?

2-port in slot 0

2-port in slot 2

4-port in slot 0

NEW QUESTION 50
A customer would like to consolidate their SAS shelves and wants to evacuate multiple shelves in parallel. What is a prerequisite for this procedure?

Purity must be upgraded to 6.x

The array chassis must be fully populated with modules.

The array usage percentage must be lower than 60%

NEW QUESTION 51
Which I/O card type is compatible across all FlashArray models?

10GBaseT

iSCSI

NEW QUESTION 52
What hardware should the Implementation Engineer find in the upgrade kit in order to perform an //X to //XL NDU?

2 QSFP cables / 3 Mellanox cards / 20 DFMDs

3 QSFP cables / 4 Mellanox cards / 10 DFMDs

4 QSFP cables / 2 Mellanox cards / 20 DFMDs

NEW QUESTION 53
An Implementation Engineer is beginning a controller upgrade. Which command should be run to stop Purity?

pureadm stop

pureadm stop –secondary

pureadm stop –controller CT0

NEW QUESTION 54
After performing a hardware upgrade from an //M20R2 to a //X20R3-EMEZZ, a customer wants to add a Direct Flash Modules data pack to replace the existing SAS Chassis Data Packs (2x 20TB DPs). What extra hardware is required?

DFM Swing shelf

SAS Swing shelf

4-port ETH card

NEW QUESTION 55
An Implementation Engineer needs to run the puresetup replace procedure on the FlashArray//X during a controller upgrade.
Which command should the Implementation Engineer run on the new controller to determine its model?

hwconfig –all

hwconfig –model

purearray list –controller

NEW QUESTION 56
What upgrade scenario required an upgrade of power supplies?

X10 > X50

X50 > X70

X50R2 > X50R3

NEW QUESTION 57
What is the rack unit height of a FlashArray//XL?

NEW QUESTION 58
An Implementation Engineer is onsite to install a new DFM data pack (DP) to CH0.BAY10-CH0.BAY19 of a FlashArray.
After adding the drives to the chassis, which command should the Implementation Engineer run to verify if the new DP is in a wide write group?

find_drive.py

puredb list drives

puredrive list –pack CH0.BAY10

NEW QUESTION 59
In a situation where iSCSI cards need to be re-used during a controller upgrade, which is a valid transfer path?

XR2 > XR3

M > XR2/3

M > XR2

NEW QUESTION 60
Which PCIe slot supports 4-port FC cards on FlashArray//XL?

NEW QUESTION 61
What command should be used to check the shelf cable connections?

purearray list –shelf

purehw list –enclosures

storage_view.py config

NEW QUESTION 62
The Customer’s Implementation Workbook specifies that the SMTP reply is “outlook.microsoft.com:587”. What correction should be made for array initialization to be successful?

Provide username and password.

Prefix the URL with “https://”.

Remove the port number.

NEW QUESTION 63
When performing an install on a FlashArray, what step should be taken first?

CT0 configuration

CT1 configuration

Code upgrade