Actual Civil-Engineering-Technology Exam Recently Updated Questions with Free Demo [Q20-Q35]

Rate this post

Actual Civil-Engineering-Technology Exam Recently Updated Questions with Free Demo

Free CTTAM Civil-Engineering-Technology Exam Questions Self-Assess Preparation

Q20. A subcontractor is completing surface rehabilitation in a mature community. What are the minimum requirements for quality that must be met?

Warranty agreement specifications

Subcontractor’s paving specifications

Developer insurance requirements

Municipality specifications

Q21. What personal protective equipment is most important when surveying near active traffic?

Hearing protection

Leather gloves

High-visibility vest

Safety glasses

Q22. What information is provided by a 5-point Proctor density test on a soil sample?

Maximum density at optimum moisture content

Maximum density at its current moisture content

Maximum moisture content of the sample

Maximum particle size within the soil sample

Q23. EXCERPT FROM MUNICIPAL BYLAW 1234 – ZONING
Section 3: Single family zone
3.1 All dwellings shall house one family.
3.2 All dwellings shall have a minimum main floor area of 120 m².
3.3 All dwellings shall be constructed a minimum of 10.0 m from the front property line, 15.0 m from the rear property line, and 1.5 m from the side property lines.
3.4 An application that does not fulfill the above requirements shall be referred to Council.

Approve the application because it meets all requirements.

Reject the application because the rear yard setback is too large.

Refer the application to Council because it does not meet the requirements.

Reject the application because one of the side yard dimensions and the main floor area are not sufficient.

Q24. A civil engineering technologist asked an engineer in training (EIT) to write a deficiency report. After a few revisions, the report is still disorganized and has errors. What would be an appropriate action to take for the technologist?

Report the EIT to the supervisor and recommend training.

Assist the EIT in re-writing the report.

Complete the document on behalf of the EIT.

Explain to the EIT the importance of meeting deadlines.

Q25. A civil engineering technologist is undertaking a final acceptance review of a subdivision. The technologist finds 35 m of deficient sidewalk and three hydrants which were not tested. As part of final acceptance, what should be done to ensure the hydrants get tested and the sidewalk is repaired?

Write down that three hydrants were not tested, and that 35 m of sidewalk was deficient.

Verbally communicate the locations of the hydrants and the sidewalk to the contractor.

Write down the locations of the hydrants and the sidewalk and forward the deficiency list to the contractor.

Request that the contractor write down the numbers and locations of the hydrants and the sidewalk.

Q26. The invert elevation of a sanitary sewer line is 98.150 m, the pipe thickness is 12 mm and its outside diameter is 600 mm. Using the image below, what is the crown elevatf m

101,238 m

101.250 m

101.488 m

101.500 m

Q27. A civil engineering technologist has been asked to check the following foundation plan drawing. How many different sizes of concrete piles are required in this project?

One

Two

Three

Four

Q28. When should soil compaction tests be completed?

During pre-design

During backfill of a trench

During record drawing completion

After paving operations

Q29. A continuous beam is supported in the middle and at both ends. It has a uniform load applied to the top. What will be the reactive forces at the supports?

They will be equal at all supports.

They will be greater in the middle than at the ends.

They will be greater at the ends than in the middle.

They will vary depending on whether the supports are fixed or not.

Q30. When calculating the total cost for a multi-year project, which of the following parameters should be considered?

Escalation cost

Cost of material

Alternate material availability

Current material delivery times

Q31. For a land development project to be initiated, which of the following documents must be submitted to the municipality for approval?

Historical resources overview

Area Structure Plan

Transportation network analysis

Neighbourhood Structure Plan

Q32. Which are five different types of driver maneuvers a technologist must consider when designing an at-grade intersection?

Turning, Merging, Weaving, Crossing, Stopping

Diverging, Merging, Weaving, Crossing, Turning

Stopping, Turning, Weaving, Converging, Swerving

Swerving, Merging, Diverging, Crossing, Converging

Q33. Which of the following tests are required as part of soil grain size analysis?

Sieve analysis for coarse grains and Atterberg limit tests for fine grains

Sieve analysis for coarse grains and hydrometer test for fine grains

Sieve analysis for fine grains and hydrometer test for coarse grains

Sieve analysis for fine grains and Atterberg limit tests for coarse grains

Q34. If a controlled product is used, stored, handled, or manufactured at a work site, what documents should be discussed at safety meetings with workers?

Material Safety Data Sheets (MSDS)

Product Application Procedures

Product Colour Board Samples

Workplace Hazardous Materials Information System (WHMIS)

Q35. A 500 mm diameter corrugated steel culvert conveys storm water under a road. The inlet end projects from the road embankment fill. How much flow (m³/s) can the culvert handle before the headwater depth is greater than the culvert diameter?

0.2 m³/s

2.0 m³/s

20 m³/s

200 m³/s